Kampotsoil

fibocom fm650

root@ROOter:~# dmesg
[    0.000000] Linux version 5.4.158 (root@2a4003c602de) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16279-5cc0535800)
) #0 Tue Aug 31 22:20:08 2021
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is YOUKU YK1
[    0.000000] Initrd not found or empty – disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000]   Normal zone: 288 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0  
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Writing ErrCtl register=00059f70
[    0.000000] Readback ErrCtl register=00059f70
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 122224K/131072K available (4830K kernel code, 201K rwdata, 1064K rodata, 1192K init, 205K
bss, 8848K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] random: get_random_bytes called from start_kernel+0x358/0x54c with crng_init=0
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running – mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015489] Calibrating delay loop… 385.02 BogoMIPS (lpj=770048)
[    0.059584] pid_max: default: 32768 minimum: 301
[    0.068971] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.083379] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.105788] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.125093] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.138686] pinctrl core: initialized pinctrl subsystem
[    0.149588] NET: Registered protocol family 16
[    0.192697] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.203766] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.216331] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.227341] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.239959] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.250971] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.263581] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.274418] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.287287] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    0.312163] clocksource: Switched to clocksource systick
[    0.324058] NET: Registered protocol family 2
[    0.332832] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.347839] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.364403] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.379570] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.393583] TCP: Hash tables configured (established 1024 bind 1024)
[    0.406370] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.419284] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.433435] NET: Registered protocol family 1
[    0.442020] PCI: CLS 0 bytes, default 32
[    0.452869] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.467063] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.488587] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.500082] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.537922] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.551706] printk: console [ttyS0] disabled
[    0.560196] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.579814] printk: console [ttyS0] enabled
[    0.596403] printk: bootconsole [early0] disabled
[    0.622023] spi spi0.0: force spi mode3
[    0.630923] spi-nor spi0.0: mx25l25635e (32768 Kbytes)
[    0.641288] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.653953] Creating 4 MTD partitions on “spi0.0”:
[    0.663509] 0x000000000000-0x000000030000 : “u-boot”
[    0.674471] 0x000000030000-0x000000040000 : “u-boot-env”
[    0.686197] 0x000000040000-0x000000050000 : “factory”
[    0.697345] 0x000000050000-0x000002000000 : “firmware”
[    0.711965] 2 uimage-fw partitions found on MTD device firmware
[    0.723843] Creating 2 MTD partitions on “firmware”:
[    0.733754] 0x000000000000-0x0000001f06da : “kernel”
[    0.744812] 0x0000001f06da-0x000001fb0000 : “rootfs”
[    0.755721] mtd: device 5 (rootfs) set to be root filesystem
[    0.768928] 1 squashfs-split partitions found on MTD device rootfs
[    0.781323] 0x000000af2000-0x000001fb0000 : “rootfs_data”
[    0.794088] libphy: Fixed MDIO Bus: probed
[    0.812160] gsw: setting port4 to ephy mode
[    0.821061] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.833670] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    0.850723] rt2880_wdt 10000120.watchdog: Initialized
[    0.862317] NET: Registered protocol family 10
[    0.875499] Segment Routing with IPv6
[    0.883037] NET: Registered protocol family 17
[    0.891984] 8021q: 802.1Q VLAN Support v1.8
[    0.908981] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.929896] Freeing unused kernel memory: 1192K
[    0.938944] This architecture does not have kernel memory protection.
[    0.951775] Run /sbin/init as init process
[    1.524113] random: fast init done
[    1.982690] init: Console is alive
[    1.989895] init: – watchdog –
[    5.406768] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.738463] usbcore: registered new interface driver usbfs
[    5.749582] usbcore: registered new interface driver hub
[    5.760305] usbcore: registered new device driver usb
[    5.811512] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[    5.835007] SCSI subsystem initialized
[    5.849189] ehci-fsl: Freescale EHCI Host controller driver
[    5.862880] ehci-platform: EHCI generic platform driver
[    5.883743] phy phy-usbphy.0: remote usb device wakeup disabled
[    5.895550] phy phy-usbphy.0: UTMI 16bit 30MHz
[    5.904407] ehci-platform 101c0000.ehci: EHCI Host Controller
[    5.915891] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    5.931813] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    5.949617] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    5.963177] hub 1-0:1.0: USB hub found
[    5.971214] hub 1-0:1.0: 1 port detected
[    5.986314] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[    6.000424] ohci-platform: OHCI generic platform driver
[    6.011249] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    6.024857] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    6.040790] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    6.077524] hub 2-0:1.0: USB hub found
[    6.085527] hub 2-0:1.0: 1 port detected
[    6.097736] uhci_hcd: USB Universal Host Controller Interface driver
[    6.141842] usbcore: registered new interface driver usb-storage
[    6.158509] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.177517] init: – preinit –
[    7.551473] random: jshn: uninitialized urandom read (4 bytes read)
[    7.655415] random: jshn: uninitialized urandom read (4 bytes read)
[    7.888875] random: jshn: uninitialized urandom read (4 bytes read)
[    8.758836] 8021q: adding VLAN 0 to HW filter on device eth0
[    8.911133] urandom_read: 4 callbacks suppressed
[    8.911143] random: procd: uninitialized urandom read (4 bytes read)
[   10.509266] mount_root: loading kmods from internal overlay
[   10.608255] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.624187] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   12.785249] jffs2: notice: (516) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum
(20 unchecked, 1 orphan) and 31 of xref (1 dead, 0 orphan) found.
[   12.817554] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   12.840864] block: extroot: not configured
[   14.093476] jffs2: notice: (514) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum
(20 unchecked, 1 orphan) and 31 of xref (1 dead, 0 orphan) found.
[   14.873502] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   14.896127] block: extroot: not configured
[   14.905906] mount_root: switching to jffs2 overlay
[   14.928650] overlayfs: upper fs does not support tmpfile.
[   14.947872] urandom-seed: Seed file not found (/etc/urandom.seed)
[   15.175047] procd: – early –
[   15.181004] procd: – watchdog –
[   15.940544] procd: – watchdog –
[   15.966893] procd: – ubus –
[   16.310371] random: ubusd: uninitialized urandom read (4 bytes read)
[   16.340542] random: ubusd: uninitialized urandom read (4 bytes read)
[   16.479286] procd: – init –
[   19.317410] kmodloader: loading kernel modules from /etc/modules.d/*
[   19.696280] urngd: jent-rng init failed, err: 2
[   19.973013] tun: Universal TUN/TAP device driver, 1.6
[   20.012469] nat46: module (version 362640b41ae52b732d9e9729e61ac555492442a3) loaded.
[   20.189122] GACT probability on
[   20.207895] Mirror/redirect action on
[   20.258676] u32 classifier
[   20.264134]     input device check on
[   20.271426]     Actions configured
[   20.336632] fuse: init (API version 7.31)
[   20.373475] usbcore: registered new interface driver cdc_acm
[   20.384823] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   20.427400] usbcore: registered new interface driver cdc_wdm
[   20.443793] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
[   20.458982] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
[   20.488194] usbcore: registered new interface driver ipheth
[   20.580663] usbcore: registered new interface driver usblp
[   20.609380] usbcore: registered new interface driver usbserial_generic
[   20.622570] usbserial: USB Serial support registered for generic
[   20.672426] xt_time: kernel timezone is -0000
[   20.685196] usbcore: registered new interface driver cdc_ether
[   20.702952] usbcore: registered new interface driver cdc_ncm
[   20.802333] usbcore: registered new interface driver huawei_cdc_ncm
[   20.921558] PPP generic driver version 2.4.2
[   20.933782] NET: Registered protocol family 24
[   20.947417] usbcore: registered new interface driver qmi_wwan
[   20.963880] usbcore: registered new interface driver rndis_host
[   21.004555] usbcore: registered new interface driver sierra
[   21.015837] usbserial: USB Serial support registered for Sierra USB modem
[   21.033862] usbcore: registered new interface driver sierra_net
[   21.058717] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   21.074398] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
[   21.120036] usbcore: registered new interface driver cdc_mbim
[   21.141327] usbcore: registered new interface driver option
[   21.152620] usbserial: USB Serial support registered for GSM modem (1-port)
[   21.175206] usbcore: registered new interface driver qcserial
[   21.186863] usbserial: USB Serial support registered for Qualcomm USB modem
[   21.228892] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device “factory”
[   21.243371] ieee80211 phy0: rt2x00_set_rt: Info – RT chipset 6352, rev 0500 detected
[   21.258841] ieee80211 phy0: rt2x00_set_rf: Info – RF chipset 7620 detected
[   21.272680] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’
[   21.386827] usbcore: registered new interface driver rt2800usb
[   21.402090] kmodloader: done loading kernel modules from /etc/modules.d/*
[   30.141762] random: crng init done
[   48.186668] 8021q: adding VLAN 0 to HW filter on device eth0
[   48.225183] br-lan: port 1(eth0.1) entered blocking state
[   48.236039] br-lan: port 1(eth0.1) entered disabled state
[   48.247252] device eth0.1 entered promiscuous mode
[   48.256856] device eth0 entered promiscuous mode
[   48.353401] br-lan: port 1(eth0.1) entered blocking state
[   48.364236] br-lan: port 1(eth0.1) entered forwarding state
[   49.190195] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   57.532167] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration start
[   57.548838] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration end
[   61.671482] ieee80211 phy0: rt2800_loft_iq_calibration: Info – LOFT Calibration Done!
[   61.691082] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[   61.719002] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 0, (gain= f, phase= 0)
[   61.738120] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[   61.766031] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 1, (gain= f, phase=3e)
[   61.784268] ieee80211 phy0: rt2800_loft_iq_calibration: Info – TX IQ Calibration Done!
[   61.813570] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=-3, Ph_rx=0
[   61.838934] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=1, Ph_rx=-2
[   61.922090] br-lan: port 2(wlan0) entered blocking state
[   61.932763] br-lan: port 2(wlan0) entered disabled state
[   61.943807] device wlan0 entered promiscuous mode
[   64.198895] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   64.211865] br-lan: port 2(wlan0) entered blocking state
[   64.222506] br-lan: port 2(wlan0) entered forwarding state
[   82.031153] device wlan0 left promiscuous mode
[   82.040248] br-lan: port 2(wlan0) entered disabled state
[   83.282597] br-lan: port 1(eth0.1) entered disabled state
[   83.450420] device eth0.1 left promiscuous mode
[   83.459757] br-lan: port 1(eth0.1) entered disabled state
[   85.031067] device eth0 left promiscuous mode
[   92.926848] 8021q: adding VLAN 0 to HW filter on device eth0
[   92.965690] br-lan: port 1(eth0.1) entered blocking state
[   92.976520] br-lan: port 1(eth0.1) entered disabled state
[   92.987724] device eth0.1 entered promiscuous mode
[   92.997329] device eth0 entered promiscuous mode
[   93.085485] br-lan: port 1(eth0.1) entered blocking state
[   93.096280] br-lan: port 1(eth0.1) entered forwarding state
[   93.943207] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   97.530167] ksmbd: kill command received
[   99.207787] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration start
[   99.224461] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration end
[  104.099802] ksmbd: kill command received
[  104.473166] ieee80211 phy0: rt2800_loft_iq_calibration: Info – LOFT Calibration Done!
[  104.492763] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[  104.520684] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 0, (gain= 1, phase= 1)
[  104.539802] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[  104.567729] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 1, (gain= 3, phase=3e)
[  104.585966] ieee80211 phy0: rt2800_loft_iq_calibration: Info – TX IQ Calibration Done!
[  104.615359] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=-4, Ph_rx=0
[  104.643159] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=0, Ph_rx=3
[  104.756494] br-lan: port 2(wlan0) entered blocking state
[  104.767170] br-lan: port 2(wlan0) entered disabled state
[  104.778293] device wlan0 entered promiscuous mode
[  106.862360] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  106.875319] br-lan: port 2(wlan0) entered blocking state
[  106.885954] br-lan: port 2(wlan0) entered forwarding state

[ 0.000000] Linux version 5.4.158 (root@2a4003c602de) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16279-5cc0535800)) #0 Tue Aug 31 22:20:08 2021
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is YOUKU YK1
[ 0.000000] Initrd not found or empty – disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=132768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00040000 [ 0.000000] Readback ErrCtl register=00040000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 122224K/131072K available (4830K kernel code, 201K rwdata, 1064K rodata, 1192K init, 205K bss, 8848K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x358/0x54c with crng_init=0 [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running – mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.015489] Calibrating delay loop… 385.02 BogoMIPS (lpj=770048) [ 0.059576] pid_max: default: 32768 minimum: 301 [ 0.068964] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.083372] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.105780] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.125086] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.138679] pinctrl core: initialized pinctrl subsystem [ 0.149580] NET: Registered protocol family 16 [ 0.192687] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.203756] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.216322] rt2880_gpio 10000638.gpio: registering 16 gpios [ 0.227331] rt2880_gpio 10000638.gpio: registering 16 irq handlers [ 0.239950] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.250962] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.263571] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.274408] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.287277] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.312151] clocksource: Switched to clocksource systick [ 0.324048] NET: Registered protocol family 2 [ 0.332822] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.347829] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.364394] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.379561] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.393573] TCP: Hash tables configured (established 1024 bind 1024) [ 0.406360] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.419274] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.433424] NET: Registered protocol family 1 [ 0.442010] PCI: CLS 0 bytes, default 32 [ 0.452857] rt-timer 10000100.timer: maximum frequency is 1220Hz [ 0.467051] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.488577] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.500073] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.537854] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.551639] printk: console [ttyS0] disabled [ 0.560115] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.579749] printk: console [ttyS0] enabled [ 0.596340] printk: bootconsole [early0] disabled [ 0.622024] spi spi0.0: force spi mode3 [ 0.630921] spi-nor spi0.0: mx25l25635e (32768 Kbytes) [ 0.641286] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.653951] Creating 4 MTD partitions on “spi0.0”: [ 0.663510] 0x000000000000-0x000000030000 : “u-boot” [ 0.674477] 0x000000030000-0x000000040000 : “u-boot-env” [ 0.686205] 0x000000040000-0x000000050000 : “factory” [ 0.697357] 0x000000050000-0x000002000000 : “firmware” [ 0.711971] 2 uimage-fw partitions found on MTD device firmware [ 0.723850] Creating 2 MTD partitions on “firmware”: [ 0.733761] 0x000000000000-0x0000001f06da : “kernel” [ 0.744819] 0x0000001f06da-0x000001fb0000 : “rootfs” [ 0.755732] mtd: device 5 (rootfs) set to be root filesystem [ 0.768916] 1 squashfs-split partitions found on MTD device rootfs [ 0.781313] 0x000000af2000-0x000001fb0000 : “rootfs_data” [ 0.794081] libphy: Fixed MDIO Bus: probed [ 0.812176] gsw: setting port4 to ephy mode [ 0.821076] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.833685] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 0.850739] rt2880_wdt 10000120.watchdog: Initialized [ 0.862336] NET: Registered protocol family 10 [ 0.875508] Segment Routing with IPv6 [ 0.883045] NET: Registered protocol family 17 [ 0.891992] 8021q: 802.1Q VLAN Support v1.8 [ 0.908965] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 0.929880] Freeing unused kernel memory: 1192K [ 0.938930] This architecture does not have kernel memory protection. [ 0.951759] Run /sbin/init as init process [ 1.524099] random: fast init done [ 1.982056] init: Console is alive [ 1.989253] init: – watchdog – [ 5.403310] kmodloader: loading kernel modules from /etc/modules-boot.d/
[ 5.734951] usbcore: registered new interface driver usbfs
[ 5.746078] usbcore: registered new interface driver hub
[ 5.756804] usbcore: registered new device driver usb
[ 5.807971] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 5.831444] SCSI subsystem initialized
[ 5.845590] ehci-fsl: Freescale EHCI Host controller driver
[ 5.859292] ehci-platform: EHCI generic platform driver
[ 5.880164] phy phy-usbphy.0: remote usb device wakeup disabled
[ 5.891971] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 5.900829] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 5.912312] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 5.928236] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 5.945887] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 5.959454] hub 1-0:1.0: USB hub found
[ 5.967490] hub 1-0:1.0: 1 port detected
[ 5.982552] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 5.996645] ohci-platform: OHCI generic platform driver
[ 6.007469] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 6.021078] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 6.037011] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 6.073772] hub 2-0:1.0: USB hub found
[ 6.081776] hub 2-0:1.0: 1 port detected
[ 6.093961] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.138346] usbcore: registered new interface driver usb-storage
[ 6.155020] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.174172] init: – preinit –
[ 6.227263] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.912728] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 7.085440] scsi host0: usb-storage 1-1:1.3
[ 7.095044] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 7.162647] scsi host1: usb-storage 1-1:1.4
[ 7.187171] random: procd: uninitialized urandom read (4 bytes read)
[ 7.627383] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.806969] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.104081] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 8.196081] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 8.215874] urandom_read: 2 callbacks suppressed
[ 8.215884] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.242239] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 8.306229] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.405388] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.988679] 8021q: adding VLAN 0 to HW filter on device eth0
[ 10.641248] mount_root: loading kmods from internal overlay
[ 10.740596] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.760042] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 13.048221] jffs2: notice: (548) jffs2_build_xattr_subsystem: complete building xattr subsystem, 33 of xdatum (25 unchecked, 8 orphan) and 45 of xref (8 dead, 0 orphan) found.
[ 13.080722] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 13.165997] block: extroot: not configured
[ 14.547006] jffs2: notice: (546) jffs2_build_xattr_subsystem: complete building xattr subsystem, 33 of xdatum (25 unchecked, 8 orphan) and 45 of xref (8 dead, 0 orphan) found.
[ 15.329412] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 15.411985] block: extroot: not configured
[ 15.422175] mount_root: switching to jffs2 overlay
[ 15.439806] overlayfs: upper fs does not support tmpfile.
[ 15.456975] urandom-seed: Seeding with /etc/urandom.seed
[ 15.714575] procd: – early –
[ 15.720567] procd: – watchdog –
[ 16.472435] procd: – watchdog –
[ 16.489142] procd: – ubus –
[ 16.947603] random: ubusd: uninitialized urandom read (4 bytes read)
[ 16.970953] random: ubusd: uninitialized urandom read (4 bytes read)
[ 17.005950] procd: – init –
[ 19.693060] kmodloader: loading kernel modules from /etc/modules.d/*
[ 20.323951] urngd: jent-rng init failed, err: 2
[ 20.425178] tun: Universal TUN/TAP device driver, 1.6
[ 20.455701] nat46: module (version 362640b41ae52b732d9e9729e61ac555492442a3) loaded.
[ 20.643624] GACT probability on
[ 20.661517] Mirror/redirect action on
[ 20.706465] u32 classifier
[ 20.711945] input device check on
[ 20.719243] Actions configured
[ 20.786521] fuse: init (API version 7.31)
[ 20.833152] usbcore: registered new interface driver cdc_acm
[ 20.844479] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 20.890895] usbcore: registered new interface driver cdc_wdm
[ 20.926420] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
[ 20.941587] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
[ 21.001743] usbcore: registered new interface driver ipheth
[ 21.152136] usbcore: registered new interface driver usblp
[ 21.203386] usbcore: registered new interface driver usbserial_generic
[ 21.216583] usbserial: USB Serial support registered for generic
[ 21.315663] xt_time: kernel timezone is -0000
[ 21.339538] usbcore: registered new interface driver cdc_ether
[ 21.374473] usbcore: registered new interface driver cdc_ncm
[ 21.517982] huawei_cdc_ncm 1-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
[ 21.530396] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
[ 21.564559] huawei_cdc_ncm 1-1:1.2: setting tx_max = 16384
[ 21.584565] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
[ 21.600807] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[ 21.613297] huawei_cdc_ncm 1-1:1.2 wwan0: register ‘huawei_cdc_ncm’ at usb-101c0000.ehci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[ 21.637365] usbcore: registered new interface driver huawei_cdc_ncm
[ 21.887774] PPP generic driver version 2.4.2
[ 21.910168] NET: Registered protocol family 24
[ 21.936249] usbcore: registered new interface driver qmi_wwan
[ 21.966839] usbcore: registered new interface driver rndis_host
[ 22.042908] usbcore: registered new interface driver sierra
[ 22.054219] usbserial: USB Serial support registered for Sierra USB modem
[ 22.103308] usbcore: registered new interface driver sierra_net
[ 22.214531] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 22.230218] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld [email protected]. All Rights Reserved.
[ 22.275630] usbcore: registered new interface driver cdc_mbim
[ 22.303883] usbcore: registered new interface driver option
[ 22.315171] usbserial: USB Serial support registered for GSM modem (1-port)
[ 22.329579] option 1-1:1.0: GSM modem (1-port) converter detected
[ 22.342071] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 22.355927] option 1-1:1.1: GSM modem (1-port) converter detected
[ 22.368498] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 22.478341] usbcore: registered new interface driver qcserial
[ 22.489999] usbserial: USB Serial support registered for Qualcomm USB modem
[ 22.582407] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device “factory”
[ 22.596894] ieee80211 phy0: rt2x00_set_rt: Info – RT chipset 6352, rev 0500 detected
[ 22.612362] ieee80211 phy0: rt2x00_set_rf: Info – RF chipset 7620 detected
[ 22.626182] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’
[ 22.864278] usbcore: registered new interface driver rt2800usb
[ 22.879675] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 32.823346] random: crng init done
[ 50.329869] 8021q: adding VLAN 0 to HW filter on device eth0
[ 50.379831] br-lan: port 1(eth0.1) entered blocking state
[ 50.390671] br-lan: port 1(eth0.1) entered disabled state
[ 50.401881] device eth0.1 entered promiscuous mode
[ 50.411481] device eth0 entered promiscuous mode
[ 50.559388] br-lan: port 1(eth0.1) entered blocking state
[ 50.570182] br-lan: port 1(eth0.1) entered forwarding state
[ 51.343844] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 59.225731] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration start
[ 59.242403] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration end
[ 64.518154] ieee80211 phy0: rt2800_loft_iq_calibration: Info – LOFT Calibration Done!
[ 64.537751] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[ 64.565661] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 0, (gain= f, phase= 1)
[ 64.584792] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[ 64.612710] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 1, (gain= 3, phase=3e)
[ 64.630947] ieee80211 phy0: rt2800_loft_iq_calibration: Info – TX IQ Calibration Done!
[ 64.677936] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=-3, Ph_rx=-2
[ 64.703468] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=0, Ph_rx=3
[ 64.863421] br-lan: port 2(wlan0) entered blocking state
[ 64.874098] br-lan: port 2(wlan0) entered disabled state
[ 64.885133] device wlan0 entered promiscuous mode
[ 67.063207] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 67.076227] br-lan: port 2(wlan0) entered blocking state
[ 67.086870] br-lan: port 2(wlan0) entered forwarding state
[ 185.345802] usb 1-1: USB disconnect, device number 2
[ 185.356263] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 185.372434] option 1-1:1.0: device disconnected
[ 185.411711] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 185.427868] option 1-1:1.1: device disconnected
[ 185.437330] huawei_cdc_ncm 1-1:1.2 wwan0: unregister ‘huawei_cdc_ncm’ usb-101c0000.ehci-1, Huawei CDC NCM device
[ 185.978695] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 186.610701] usb 1-1: device not accepting address 3, error -71
[ 186.795129] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 187.438661] usb 1-1: device not accepting address 4, error -71
[ 187.490635] usb usb1-port1: attempt power cycle
[ 187.946665] usb 1-1: new high-speed USB device number 5 using ehci-platform
[ 188.040342] option 1-1:1.0: GSM modem (1-port) converter detected
[ 188.052901] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 188.067512] option 1-1:1.1: GSM modem (1-port) converter detected
[ 188.080376] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 188.346682] huawei_cdc_ncm 1-1:1.2: bind() failure
[ 188.357268] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 188.467477] scsi host0: usb-storage 1-1:1.3
[ 188.476926] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 188.595676] scsi host1: usb-storage 1-1:1.4
[ 188.654938] usb 1-1: USB disconnect, device number 5
[ 188.665446] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 188.681690] option 1-1:1.0: device disconnected
[ 188.871515] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 188.887699] option 1-1:1.1: device disconnected
[ 189.350737] usb 1-1: new high-speed USB device number 6 using ehci-platform
[ 189.754689] usb 1-1: device descriptor read/64, error -71
[ 190.218703] usb 1-1: device descriptor read/64, error -71
[ 190.462631] usb 1-1: new high-speed USB device number 7 using ehci-platform
[ 191.050686] usb 1-1: device not accepting address 7, error -71
[ 191.082838] usb usb1-port1: attempt power cycle
[ 191.514674] usb 1-1: new high-speed USB device number 8 using ehci-platform
[ 191.599826] option 1-1:1.0: GSM modem (1-port) converter detected
[ 191.612398] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 191.626895] option 1-1:1.1: GSM modem (1-port) converter detected
[ 191.639424] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 191.754750] huawei_cdc_ncm 1-1:1.2: bind() failure
[ 191.765216] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 191.807068] scsi host0: usb-storage 1-1:1.3
[ 191.816398] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 191.854723] scsi host1: usb-storage 1-1:1.4
[ 191.883525] usb 1-1: USB disconnect, device number 8
[ 191.893950] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 191.910117] option 1-1:1.0: device disconnected
[ 191.919690] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 191.935840] option 1-1:1.1: device disconnected
[ 192.358712] usb 1-1: new high-speed USB device number 9 using ehci-platform
[ 192.790663] usb 1-1: device descriptor read/64, error -71
[ 193.046680] usb 1-1: device descriptor read/64, error -71
[ 193.498664] usb 1-1: new high-speed USB device number 10 using ehci-platform
[ 193.699565] option 1-1:1.0: GSM modem (1-port) converter detected
[ 193.712130] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 193.726643] option 1-1:1.1: GSM modem (1-port) converter detected
[ 193.739142] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 193.934739] huawei_cdc_ncm 1-1:1.2: bind() failure
[ 193.945187] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 194.027555] scsi host0: usb-storage 1-1:1.3
[ 194.036904] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 194.102649] scsi host1: usb-storage 1-1:1.4
[ 194.156656] usb 1-1: USB disconnect, device number 10
[ 194.167269] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 194.183428] option 1-1:1.0: device disconnected
[ 194.193032] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 194.209259] option 1-1:1.1: device disconnected
[ 194.630677] usb 1-1: new high-speed USB device number 11 using ehci-platform
[ 195.230677] usb 1-1: device not accepting address 11, error -71
[ 195.622702] usb 1-1: new high-speed USB device number 12 using ehci-platform
[ 196.250784] usb 1-1: device not accepting address 12, error -71
[ 196.293392] usb usb1-port1: attempt power cycle
[ 196.750667] usb 1-1: new high-speed USB device number 13 using ehci-platform
[ 196.799697] option 1-1:1.0: GSM modem (1-port) converter detected
[ 196.812252] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 196.826793] option 1-1:1.1: GSM modem (1-port) converter detected
[ 196.839306] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 196.935861] huawei_cdc_ncm 1-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
[ 196.948255] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
[ 196.982488] huawei_cdc_ncm 1-1:1.2: setting tx_max = 16384
[ 197.006639] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
[ 197.022910] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[ 197.035516] huawei_cdc_ncm 1-1:1.2 wwan0: register ‘huawei_cdc_ncm’ at usb-101c0000.ehci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[ 197.059780] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 197.330689] scsi host0: usb-storage 1-1:1.3
[ 197.339990] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 197.466743] scsi host1: usb-storage 1-1:1.4
[ 197.550872] usb usb1-port1: disabled by hub (EMI?), re-enabling…
[ 197.563258] usb 1-1: USB disconnect, device number 13
[ 197.573802] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 197.590479] option 1-1:1.0: device disconnected
[ 197.600372] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 197.616546] option 1-1:1.1: device disconnected
[ 197.626003] huawei_cdc_ncm 1-1:1.2 wwan0: unregister ‘huawei_cdc_ncm’ usb-101c0000.ehci-1, Huawei CDC NCM device
[ 198.386707] usb 1-1: new high-speed USB device number 14 using ehci-platform
[ 198.602732] usb 1-1: device descriptor read/64, error -71
[ 199.066668] usb 1-1: device descriptor read/64, error -71
[ 199.310704] usb 1-1: new high-speed USB device number 15 using ehci-platform
[ 199.730733] usb 1-1: device descriptor read/64, error -71
[ 200.398670] usb 1-1: device not accepting address 15, error -71
[ 200.462673] usb usb1-port1: attempt power cycle
[ 200.938676] usb 1-1: new high-speed USB device number 16 using ehci-platform
[ 201.446730] usb 1-1: device not accepting address 16, error -71
[ 201.850694] usb 1-1: new high-speed USB device number 17 using ehci-platform
[ 201.975705] option 1-1:1.0: GSM modem (1-port) converter detected
[ 201.988279] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 202.002782] option 1-1:1.1: GSM modem (1-port) converter detected
[ 202.015310] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 202.302783] huawei_cdc_ncm 1-1:1.2: bind() failure
[ 202.313291] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 202.450917] scsi host0: usb-storage 1-1:1.3
[ 202.460236] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 202.596929] scsi host1: usb-storage 1-1:1.4
[ 202.666689] usb 1-1: USB disconnect, device number 17
[ 202.677244] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 202.693412] option 1-1:1.0: device disconnected
[ 202.703072] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 202.719217] option 1-1:1.1: device disconnected
[ 203.342691] usb 1-1: new high-speed USB device number 18 using ehci-platform
[ 203.758699] usb 1-1: device descriptor read/64, error -71
[ 204.226669] usb 1-1: device descriptor read/64, error -71
[ 204.470668] usb 1-1: new high-speed USB device number 19 using ehci-platform
[ 204.854674] usb 1-1: device descriptor read/64, error -71
[ 205.110662] usb 1-1: device descriptor read/64, error -71
[ 205.226762] usb usb1-port1: attempt power cycle
[ 205.658676] usb 1-1: new high-speed USB device number 20 using ehci-platform
[ 205.719575] option 1-1:1.0: GSM modem (1-port) converter detected
[ 205.732132] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 205.746632] option 1-1:1.1: GSM modem (1-port) converter detected
[ 205.759117] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 205.959848] huawei_cdc_ncm 1-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
[ 205.972243] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
[ 206.026712] huawei_cdc_ncm 1-1:1.2: setting tx_max = 16384
[ 206.062826] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
[ 206.079595] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[ 206.092412] huawei_cdc_ncm 1-1:1.2 wwan0: register ‘huawei_cdc_ncm’ at usb-101c0000.ehci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[ 206.116683] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 206.280996] scsi host0: usb-storage 1-1:1.3
[ 206.290347] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 206.350845] scsi host1: usb-storage 1-1:1.4
[ 207.315857] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 207.379736] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 207.420166] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 241.638686] usb 1-1: USB disconnect, device number 20
[ 241.649363] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 241.665505] option 1-1:1.0: device disconnected
[ 241.675116] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 241.691306] option 1-1:1.1: device disconnected
[ 241.989327] huawei_cdc_ncm 1-1:1.2 wwan0: unregister ‘huawei_cdc_ncm’ usb-101c0000.ehci-1, Huawei CDC NCM device
[ 242.425306] usb 1-1: new high-speed USB device number 21 using ehci-platform
[ 242.853347] usb 1-1: device descriptor read/64, error -71
[ 243.317364] usb 1-1: device descriptor read/64, error -71
[ 243.769290] usb 1-1: new high-speed USB device number 22 using ehci-platform
[ 243.941330] usb 1-1: device descriptor read/64, error -71
[ 244.609340] usb 1-1: device not accepting address 22, error -71
[ 244.628064] usb usb1-port1: attempt power cycle
[ 245.061276] usb 1-1: new high-speed USB device number 23 using ehci-platform
[ 245.509308] usb 1-1: device not accepting address 23, error -71
[ 245.881388] usb 1-1: new high-speed USB device number 24 using ehci-platform
[ 245.978405] option 1-1:1.0: GSM modem (1-port) converter detected
[ 245.990964] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 246.005999] option 1-1:1.1: GSM modem (1-port) converter detected
[ 246.018788] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 246.370155] huawei_cdc_ncm 1-1:1.2: bind() failure
[ 246.380623] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 246.506385] scsi host0: usb-storage 1-1:1.3
[ 246.515869] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 246.601330] scsi host1: usb-storage 1-1:1.4
[ 246.652536] usb 1-1: USB disconnect, device number 24
[ 246.663159] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 246.679356] option 1-1:1.0: device disconnected
[ 246.837512] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 246.853654] option 1-1:1.1: device disconnected
[ 247.273314] usb 1-1: new high-speed USB device number 25 using ehci-platform
[ 247.697380] usb 1-1: device descriptor read/64, error -71
[ 248.161300] usb 1-1: device descriptor read/64, error -71
[ 248.613378] usb 1-1: new high-speed USB device number 26 using ehci-platform
[ 248.805292] usb 1-1: device descriptor read/64, error -71
[ 249.062440] usb 1-1: device descriptor read/64, error -71
[ 249.181426] usb usb1-port1: attempt power cycle
[ 249.617336] usb 1-1: new high-speed USB device number 27 using ehci-platform
[ 249.713873] option 1-1:1.0: GSM modem (1-port) converter detected
[ 249.726448] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 249.740851] option 1-1:1.1: GSM modem (1-port) converter detected
[ 249.753418] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 250.050493] huawei_cdc_ncm 1-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
[ 250.062886] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
[ 250.178911] huawei_cdc_ncm 1-1:1.2: setting tx_max = 16384
[ 250.234323] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
[ 250.250627] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[ 250.263190] huawei_cdc_ncm 1-1:1.2 wwan0: register ‘huawei_cdc_ncm’ at usb-101c0000.ehci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[ 250.287451] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 250.722706] scsi host0: usb-storage 1-1:1.3
[ 250.732021] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 250.878077] scsi host1: usb-storage 1-1:1.4
[ 251.763049] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 251.890934] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 251.949186] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 261.408446] usb 1-1: USB disconnect, device number 27
[ 261.419067] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 261.435238] option 1-1:1.0: device disconnected
[ 261.444807] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 261.461034] option 1-1:1.1: device disconnected
[ 261.470517] huawei_cdc_ncm 1-1:1.2 wwan0: unregister ‘huawei_cdc_ncm’ usb-101c0000.ehci-1, Huawei CDC NCM device
[ 262.005341] usb 1-1: new high-speed USB device number 28 using ehci-platform
[ 262.230271] option 1-1:1.0: GSM modem (1-port) converter detected
[ 262.242824] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 262.257334] option 1-1:1.1: GSM modem (1-port) converter detected
[ 262.269821] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 262.610531] huawei_cdc_ncm 1-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
[ 262.622921] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
[ 262.747515] huawei_cdc_ncm 1-1:1.2: setting tx_max = 16384
[ 262.821337] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
[ 262.837618] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[ 262.850228] huawei_cdc_ncm 1-1:1.2 wwan0: register ‘huawei_cdc_ncm’ at usb-101c0000.ehci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[ 262.874495] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 263.222161] scsi host0: usb-storage 1-1:1.3
[ 263.231493] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 263.357311] scsi host1: usb-storage 1-1:1.4
[ 264.242376] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 264.370382] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 264.462540] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 387.647230] usb 1-1: USB disconnect, device number 28
[ 387.657832] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 387.673974] option 1-1:1.0: device disconnected
[ 387.683560] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 387.699728] option 1-1:1.1: device disconnected
[ 387.709192] huawei_cdc_ncm 1-1:1.2 wwan0: unregister ‘huawei_cdc_ncm’ usb-101c0000.ehci-1, Huawei CDC NCM device
[ 394.900332] usb 1-1: new high-speed USB device number 29 using ehci-platform
[ 395.019219] option 1-1:1.0: GSM modem (1-port) converter detected
[ 395.031750] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 395.046197] option 1-1:1.1: GSM modem (1-port) converter detected
[ 395.058775] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 395.159954] huawei_cdc_ncm 1-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
[ 395.172359] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
[ 395.210787] huawei_cdc_ncm 1-1:1.2: setting tx_max = 16384
[ 395.242738] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
[ 395.259453] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[ 395.272260] huawei_cdc_ncm 1-1:1.2 wwan0: register ‘huawei_cdc_ncm’ at usb-101c0000.ehci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[ 395.296593] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 395.475007] scsi host0: usb-storage 1-1:1.3
[ 395.484382] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 395.530946] scsi host1: usb-storage 1-1:1.4
[ 396.507966] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 396.571854] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 396.628329] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 402.757165] usb usb1-port1: disabled by hub (EMI?), re-enabling…
[ 402.769556] usb 1-1: USB disconnect, device number 29
[ 402.780099] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 402.796319] option 1-1:1.0: device disconnected
[ 402.805893] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 402.822076] option 1-1:1.1: device disconnected
[ 402.831513] huawei_cdc_ncm 1-1:1.2 wwan0: unregister ‘huawei_cdc_ncm’ usb-101c0000.ehci-1, Huawei CDC NCM device
[ 403.298120] usb 1-1: new high-speed USB device number 30 using ehci-platform
[ 403.486154] usb 1-1: device descriptor read/64, error -71
[ 403.950155] usb 1-1: device descriptor read/64, error -71
[ 404.402163] usb 1-1: new high-speed USB device number 31 using ehci-platform
[ 404.798382] usb 1-1: device descriptor read/64, error -71
[ 405.466130] usb 1-1: device not accepting address 31, error -71
[ 405.498128] usb usb1-port1: attempt power cycle
[ 405.946158] usb 1-1: new high-speed USB device number 32 using ehci-platform
[ 406.414171] usb 1-1: device not accepting address 32, error -71
[ 406.578170] usb 1-1: new high-speed USB device number 33 using ehci-platform
[ 406.655611] option 1-1:1.0: GSM modem (1-port) converter detected
[ 406.668237] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 406.682726] option 1-1:1.1: GSM modem (1-port) converter detected
[ 406.695237] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 406.838517] huawei_cdc_ncm 1-1:1.2: bind() failure
[ 406.848974] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 406.890454] scsi host0: usb-storage 1-1:1.3
[ 406.899774] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 406.938333] scsi host1: usb-storage 1-1:1.4
[ 406.983142] usb 1-1: USB disconnect, device number 33
[ 406.993754] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 407.009909] option 1-1:1.0: device disconnected
[ 407.019483] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 407.035638] option 1-1:1.1: device disconnected
[ 407.618172] usb 1-1: new high-speed USB device number 34 using ehci-platform
[ 407.986156] usb 1-1: device descriptor read/64, error -71
[ 408.450130] usb 1-1: device descriptor read/64, error -71
[ 408.902146] usb 1-1: new high-speed USB device number 35 using ehci-platform
[ 409.066248] usb 1-1: device descriptor read/64, error -71
[ 409.530131] usb 1-1: device descriptor read/64, error -71
[ 409.646397] usb usb1-port1: attempt power cycle
[ 410.082124] usb 1-1: new high-speed USB device number 36 using ehci-platform
[ 410.134925] option 1-1:1.0: GSM modem (1-port) converter detected
[ 410.147480] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 410.162013] option 1-1:1.1: GSM modem (1-port) converter detected
[ 410.174541] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 410.267206] huawei_cdc_ncm 1-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
[ 410.279607] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
[ 410.314115] huawei_cdc_ncm 1-1:1.2: setting tx_max = 16384
[ 410.338116] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
[ 410.354457] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
[ 410.367074] huawei_cdc_ncm 1-1:1.2 wwan0: register ‘huawei_cdc_ncm’ at usb-101c0000.ehci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[ 410.391327] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 410.486158] scsi host0: usb-storage 1-1:1.3
[ 410.495455] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 410.553682] scsi host1: usb-storage 1-1:1.4
[ 410.586297] usb 1-1: USB disconnect, device number 36
[ 410.597293] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 410.613481] option 1-1:1.0: device disconnected
[ 410.623308] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 410.639479] option 1-1:1.1: device disconnected
[ 410.648938] huawei_cdc_ncm 1-1:1.2 wwan0: unregister ‘huawei_cdc_ncm’ usb-101c0000.ehci-1, Huawei CDC NCM device
[ 411.186158] usb 1-1: new high-speed USB device number 37 using ehci-platform
[ 411.602219] usb 1-1: device descriptor read/64, error -71
[ 412.066165] usb 1-1: device descriptor read/64, error -71
[ 412.518150] usb 1-1: new high-speed USB device number 38 using ehci-platform
[ 412.703317] option 1-1:1.0: GSM modem (1-port) converter detected
[ 412.715989] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 412.730489] option 1-1:1.1: GSM modem (1-port) converter detected
[ 412.742991] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 412.886283] huawei_cdc_ncm 1-1:1.2: bind() failure
[ 412.896785] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 412.955268] scsi host0: usb-storage 1-1:1.3
[ 412.964618] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 413.014379] scsi host1: usb-storage 1-1:1.4
[ 413.061913] usb 1-1: USB disconnect, device number 38
[ 413.072497] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 413.088924] option 1-1:1.0: device disconnected
[ 413.098978] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 413.115155] option 1-1:1.1: device disconnected
[ 413.502173] usb 1-1: new high-speed USB device number 39 using ehci-platform
[ 413.894123] usb 1-1: device descriptor read/64, error -71
[ 414.358140] usb 1-1: device descriptor read/64, error -71
[ 414.810116] usb 1-1: new high-speed USB device number 40 using ehci-platform
[ 415.390165] usb 1-1: device not accepting address 40, error -71
[ 415.430131] usb usb1-port1: attempt power cycle
[ 415.878123] usb 1-1: new high-speed USB device number 41 using ehci-platform
[ 416.338168] usb 1-1: device not accepting address 41, error -71
[ 416.730135] usb 1-1: new high-speed USB device number 42 using ehci-platform
[ 416.803056] option 1-1:1.0: GSM modem (1-port) converter detected
[ 416.815620] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 416.830208] option 1-1:1.1: GSM modem (1-port) converter detected
[ 416.842707] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 417.070475] huawei_cdc_ncm 1-1:1.2: bind() failure
[ 417.080941] usb-storage 1-1:1.3: USB Mass Storage device detected
[ 417.170143] scsi host0: usb-storage 1-1:1.3
[ 417.179433] usb-storage 1-1:1.4: USB Mass Storage device detected
[ 417.248403] scsi host1: usb-storage 1-1:1.4
[ 417.319639] usb 1-1: USB disconnect, device number 42
[ 417.330295] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 417.346434] option 1-1:1.0: device disconnected
[ 417.356004] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 417.372154] option 1-1:1.1: device disconnected
[ 417.914170] usb 1-1: new high-speed USB device number 43 using ehci-platform
[ 418.298164] usb 1-1: device descriptor read/64, error -71
[ 418.762188] usb 1-1: device descriptor read/64, error -71
[ 419.214162] usb 1-1: new high-speed USB device number 44 using ehci-platform
[ 419.602190] usb 1-1: device descriptor read/64, error -71
[ 420.066203] usb 1-1: device descriptor read/64, error -71
[ 420.182207] usb usb1-port1: attempt power cycle
[ 420.622174] usb 1-1: new high-speed USB device number 45 using ehci-platform
[ 420.686155] usb 1-1: device descriptor read/8, error -71
[ 420.834731] usb 1-1: device descriptor read/8, error -71
[ 421.286191] usb 1-1: new high-speed USB device number 46 using ehci-platform
[ 421.734201] usb 1-1: device not accepting address 46, error -71
[ 421.770133] usb usb1-port1: unable to enumerate USB device
[ 422.130140] usb 2-1: new full-speed USB device number 2 using ohci-platform
[ 422.429160] usb 2-1: not running at top speed; connect to a high speed hub
[ 422.518761] option 2-1:1.0: GSM modem (1-port) converter detected
[ 422.531315] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 422.545737] option 2-1:1.1: GSM modem (1-port) converter detected
[ 422.558338] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 422.767172] huawei_cdc_ncm 2-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
[ 422.779576] huawei_cdc_ncm 2-1:1.2: setting rx_max = 16384
[ 422.858167] huawei_cdc_ncm 2-1:1.2: setting tx_max = 16384
[ 422.890143] huawei_cdc_ncm 2-1:1.2: NDP will be placed at end of frame for this device.
[ 422.906428] huawei_cdc_ncm 2-1:1.2: cdc-wdm0: USB WDM device
[ 422.919025] huawei_cdc_ncm 2-1:1.2 wwan0: register ‘huawei_cdc_ncm’ at usb-101c1000.ohci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
[ 422.943291] usb-storage 2-1:1.3: USB Mass Storage device detected
[ 423.120808] scsi host0: usb-storage 2-1:1.3
[ 423.130232] usb-storage 2-1:1.4: USB Mass Storage device detected
[ 423.231018] scsi host1: usb-storage 2-1:1.4
[ 424.165299] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 424.261320] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 424.345190] sd 1:0:0:0: [sda] Attached SCSI removable disk