dmesg cf-e3

root@ROOter:~# dmesg
[ 0.000000] Linux version 4.14.215 (dairyman@Compaq6300) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11278-8055e38794)) #0 Tue Jan 19 13:10:02 2021
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is COMFAST CF-E5/E7
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty – disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8052d990, node_mem_map 81007540
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x47c with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=132768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 58148K/65536K available (3852K kernel code, 144K rwdata, 924K rodata, 1216K init, 204K bss, 7388K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 650.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns [ 0.000010] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns [ 0.008266] Calibrating delay loop… 432.53 BogoMIPS (lpj=2162688) [ 0.074874] pid_max: default: 32768 minimum: 301 [ 0.079964] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.086938] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.098868] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.109316] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.115848] pinctrl core: initialized pinctrl subsystem [ 0.122552] NET: Registered protocol family 16 [ 0.158264] clocksource: Switched to clocksource MIPS [ 0.164872] NET: Registered protocol family 2 [ 0.170419] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.177790] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.184583] TCP: Hash tables configured (established 1024 bind 1024) [ 0.191501] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.197683] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.204659] NET: Registered protocol family 1 [ 0.209343] PCI: CLS 0 bytes, default 32 [ 0.212974] Crashlog allocated RAM at address 0x3f00000 [ 0.220196] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.232566] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.238771] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.260361] io scheduler noop registered [ 0.264505] io scheduler deadline registered (default) [ 0.270333] ar7200-usb-phy 18030000.usb-phy: phy reset is missing [ 0.278994] pinctrl-single 1804002c.pinmux: 576 pins at pa b804002c size 72 [ 0.287458] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.295066] console [ttyS0] disabled [ 0.298962] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A [ 0.308067] console [ttyS0] enabled [ 0.315637] bootconsole [early0] disabled [ 0.340721] m25p80 spi0.0: s25fl064k (8192 Kbytes) [ 0.345740] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.352321] Creating 4 MTD partitions on “spi0.0”: [ 0.357285] 0x000000000000-0x000000010000 : “u-boot” [ 0.363395] 0x000000010000-0x000000020000 : “art” [ 0.369230] 0x000000020000-0x000000ff0000 : “firmware” [ 0.374557] mtd: partition “firmware” extends beyond the end of device “spi0.0” — size truncated to 0x7e0000 [ 0.388189] 2 uimage-fw partitions found on MTD device firmware [ 0.394394] Creating 2 MTD partitions on “firmware”: [ 0.399548] 0x000000000000-0x0000001a0000 : “kernel” [ 0.405555] 0x0000001a0000-0x0000007e0000 : “rootfs” [ 0.411544] mtd: device 4 (rootfs) set to be root filesystem [ 0.417440] 1 squashfs-split partitions found on MTD device rootfs [ 0.423910] 0x000000710000-0x0000007e0000 : “rootfs_data” [ 0.430365] 0x000000ff0000-0x000001000000 : “art-backup” [ 0.435866] mtd: partition “art-backup” is out of reach — disabled [ 0.444570] libphy: Fixed MDIO Bus: probed [ 0.789384] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 1.468681] libphy: ag71xx_mdio: probed [ 1.474200] libphy: ar8xxx-mdio: probed [ 1.487556] switch0: Atheros AR8229 rev. 1 switch registered on mdio-bus.0 [ 1.540057] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY] [ 1.550140] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii [ 1.559408] NET: Registered protocol family 10 [ 1.570246] Segment Routing with IPv6 [ 1.574143] NET: Registered protocol family 17 [ 1.578881] 8021q: 802.1Q VLAN Support v1.8 [ 1.920596] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:1f:04 [uid=004dd042, driver=Generic PHY] [ 1.931473] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii [ 1.945622] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.962899] Freeing unused kernel memory: 1216K [ 1.967586] This architecture does not have kernel memory protection. [ 2.538330] random: fast init done [ 2.722761] init: Console is alive [ 2.726568] init: – watchdog – [ 4.325766] kmodloader: loading kernel modules from /etc/modules-boot.d/
[ 4.515779] usbcore: registered new interface driver usbfs
[ 4.521622] usbcore: registered new interface driver hub
[ 4.527202] usbcore: registered new device driver usb
[ 4.539836] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 4.548985] ehci-platform: EHCI generic platform driver
[ 4.554686] ehci-platform 1b000000.usb: EHCI Host Controller
[ 4.560656] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 4.568894] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000
[ 4.598291] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 4.605723] hub 1-0:1.0: USB hub found
[ 4.610122] hub 1-0:1.0: 1 port detected
[ 4.618360] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 4.627045] ohci-platform: OHCI generic platform driver
[ 4.635420] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.643610] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.652844] init: – preinit –
[ 5.114319] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 5.705295] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.846454] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.955303] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.645654] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.699513] eth0: link up (1000Mbps/Full duplex)
[ 7.704338] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.968589] jffs2: notice: (444) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (2 unchecked, 2 orphan) and 22 of xref (2 dead, 0 orphan) found.
[ 9.986380] mount_root: switching to jffs2 overlay
[ 10.060802] overlayfs: upper fs does not support tmpfile.
[ 10.072284] urandom-seed: Seeding with /etc/urandom.seed
[ 10.260349] eth0: link down
[ 10.277739] procd: – early –
[ 10.282241] procd: – watchdog –
[ 11.162672] procd: – watchdog –
[ 11.166307] procd: – ubus –
[ 11.318382] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 11.358409] urandom_read: 4 callbacks suppressed
[ 11.358419] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.378984] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.394753] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.409571] procd: – init –
[ 13.600041] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.621461] tun: Universal TUN/TAP device driver, 1.6
[ 13.681620] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.719974] Netfilter messages via NETLINK v0.30.
[ 13.740962] ip_set: protocol 6
[ 13.880388] Mirror/redirect action on
[ 13.935419] u32 classifier
[ 13.938236] input device check on
[ 13.942114] Actions configured
[ 14.067980] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 14.121334] usbcore: registered new interface driver cdc_acm
[ 14.127195] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 14.138487] urngd: v1.0.2 started.
[ 14.151212] usbcore: registered new interface driver cdc_wdm
[ 14.178709] Loading modules backported from Linux version v4.19.161-0-gdaefdc9eb24b
[ 14.186635] Backport generated by backports.git v4.19.161-1-0-g4bb568fe
[ 14.235828] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.287210] ctnetlink v0.93: registering with nfnetlink.
[ 14.516799] usbcore: registered new interface driver usblp
[ 14.548832] usbcore: registered new interface driver usbserial
[ 14.554950] usbcore: registered new interface driver usbserial_generic
[ 14.561862] usbserial: USB Serial support registered for generic
[ 14.606455] wireguard: WireGuard 1.0.20200611 loaded. See www.wireguard.com for information.
[ 14.615276] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld [email protected]. All Rights Reserved.
[ 14.630798] random: crng init done
[ 14.734721] xt_time: kernel timezone is -0000
[ 14.757231] cdc_ether 1-1:1.0 eth2: register ‘cdc_ether’ at usb-1b000000.usb-1, CDC Ethernet Device, 00:a0:c6:00:00:00
[ 14.768723] usbcore: registered new interface driver cdc_ether
[ 14.818731] usbcore: registered new interface driver cdc_ncm
[ 14.965620] usbcore: registered new interface driver huawei_cdc_ncm
[ 15.212641] PPP generic driver version 2.4.2
[ 15.239987] NET: Registered protocol family 24
[ 15.264082] usbcore: registered new interface driver qmi_wwan
[ 15.301349] usbcore: registered new interface driver rndis_host
[ 15.341303] usbcore: registered new interface driver sierra
[ 15.347158] usbserial: USB Serial support registered for Sierra USB modem
[ 15.380932] usbcore: registered new interface driver sierra_net
[ 15.481035] usbcore: registered new interface driver cdc_mbim
[ 15.500922] usbcore: registered new interface driver option
[ 15.506765] usbserial: USB Serial support registered for GSM modem (1-port)
[ 15.534421] usbcore: registered new interface driver qcserial
[ 15.540547] usbserial: USB Serial support registered for Qualcomm USB modem
[ 15.611505] usbcore: registered new interface driver rt2800usb
[ 15.647853] ath: EEPROM regdomain: 0x0
[ 15.647867] ath: EEPROM indicates default country code should be used
[ 15.647870] ath: doing EEPROM country->regdmn map search
[ 15.647890] ath: country maps to regdmn code: 0x3a
[ 15.647896] ath: Country alpha2 being used: US
[ 15.647899] ath: Regpair used: 0x3a
[ 15.662971] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’
[ 15.665076] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=12
[ 15.778833] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 34.507657] eth0: link up (1000Mbps/Full duplex)
[ 34.516436] br-lan: port 1(eth0) entered blocking state
[ 34.521934] br-lan: port 1(eth0) entered disabled state
[ 34.527717] device eth0 entered promiscuous mode
[ 34.575471] br-lan: port 1(eth0) entered blocking state
[ 34.580962] br-lan: port 1(eth0) entered forwarding state
[ 34.586802] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 34.730401] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 35.620053] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 36.605582] usb 1-1: USB disconnect, device number 3
[ 36.610980] cdc_ether 1-1:1.0 eth2: unregister ‘cdc_ether’ usb-1b000000.usb-1, CDC Ethernet Device
[ 39.761928] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 39.841239] br-lan: port 2(wlan0) entered blocking state
[ 39.846751] br-lan: port 2(wlan0) entered disabled state
[ 39.852771] device wlan0 entered promiscuous mode
[ 41.963714] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 41.970612] br-lan: port 2(wlan0) entered blocking state
[ 41.976111] br-lan: port 2(wlan0) entered forwarding state

---