root@ROOter:~# dmesg
[ 0.000000] Linux version 5.4.158 (root@2a4003c602de) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16279-5cc0535800)
) #0 Tue Aug 31 22:20:08 2021
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is YOUKU YK1
[ 0.000000] Initrd not found or empty – disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00059f70
[ 0.000000] Readback ErrCtl register=00059f70
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 122224K/131072K available (4830K kernel code, 201K rwdata, 1064K rodata, 1192K init, 205K
bss, 8848K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from start_kernel+0x358/0x54c with crng_init=0
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running – mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015489] Calibrating delay loop… 385.02 BogoMIPS (lpj=770048)
[ 0.059584] pid_max: default: 32768 minimum: 301
[ 0.068971] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.083379] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105788] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.125093] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.138686] pinctrl core: initialized pinctrl subsystem
[ 0.149588] NET: Registered protocol family 16
[ 0.192697] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.203766] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.216331] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.227341] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.239959] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.250971] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.263581] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.274418] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.287287] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.312163] clocksource: Switched to clocksource systick
[ 0.324058] NET: Registered protocol family 2
[ 0.332832] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.347839] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.364403] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.379570] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.393583] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.406370] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.419284] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.433435] NET: Registered protocol family 1
[ 0.442020] PCI: CLS 0 bytes, default 32
[ 0.452869] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.467063] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.488587] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.500082] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.537922] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.551706] printk: console [ttyS0] disabled
[ 0.560196] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.579814] printk: console [ttyS0] enabled
[ 0.596403] printk: bootconsole [early0] disabled
[ 0.622023] spi spi0.0: force spi mode3
[ 0.630923] spi-nor spi0.0: mx25l25635e (32768 Kbytes)
[ 0.641288] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.653953] Creating 4 MTD partitions on “spi0.0”:
[ 0.663509] 0x000000000000-0x000000030000 : “u-boot”
[ 0.674471] 0x000000030000-0x000000040000 : “u-boot-env”
[ 0.686197] 0x000000040000-0x000000050000 : “factory”
[ 0.697345] 0x000000050000-0x000002000000 : “firmware”
[ 0.711965] 2 uimage-fw partitions found on MTD device firmware
[ 0.723843] Creating 2 MTD partitions on “firmware”:
[ 0.733754] 0x000000000000-0x0000001f06da : “kernel”
[ 0.744812] 0x0000001f06da-0x000001fb0000 : “rootfs”
[ 0.755721] mtd: device 5 (rootfs) set to be root filesystem
[ 0.768928] 1 squashfs-split partitions found on MTD device rootfs
[ 0.781323] 0x000000af2000-0x000001fb0000 : “rootfs_data”
[ 0.794088] libphy: Fixed MDIO Bus: probed
[ 0.812160] gsw: setting port4 to ephy mode
[ 0.821061] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.833670] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.850723] rt2880_wdt 10000120.watchdog: Initialized
[ 0.862317] NET: Registered protocol family 10
[ 0.875499] Segment Routing with IPv6
[ 0.883037] NET: Registered protocol family 17
[ 0.891984] 8021q: 802.1Q VLAN Support v1.8
[ 0.908981] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.929896] Freeing unused kernel memory: 1192K
[ 0.938944] This architecture does not have kernel memory protection.
[ 0.951775] Run /sbin/init as init process
[ 1.524113] random: fast init done
[ 1.982690] init: Console is alive
[ 1.989895] init: – watchdog –
[ 5.406768] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.738463] usbcore: registered new interface driver usbfs
[ 5.749582] usbcore: registered new interface driver hub
[ 5.760305] usbcore: registered new device driver usb
[ 5.811512] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 5.835007] SCSI subsystem initialized
[ 5.849189] ehci-fsl: Freescale EHCI Host controller driver
[ 5.862880] ehci-platform: EHCI generic platform driver
[ 5.883743] phy phy-usbphy.0: remote usb device wakeup disabled
[ 5.895550] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 5.904407] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 5.915891] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 5.931813] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 5.949617] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 5.963177] hub 1-0:1.0: USB hub found
[ 5.971214] hub 1-0:1.0: 1 port detected
[ 5.986314] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 6.000424] ohci-platform: OHCI generic platform driver
[ 6.011249] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 6.024857] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 6.040790] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 6.077524] hub 2-0:1.0: USB hub found
[ 6.085527] hub 2-0:1.0: 1 port detected
[ 6.097736] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.141842] usbcore: registered new interface driver usb-storage
[ 6.158509] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.177517] init: – preinit –
[ 7.551473] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.655415] random: jshn: uninitialized urandom read (4 bytes read)
[ 7.888875] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.758836] 8021q: adding VLAN 0 to HW filter on device eth0
[ 8.911133] urandom_read: 4 callbacks suppressed
[ 8.911143] random: procd: uninitialized urandom read (4 bytes read)
[ 10.509266] mount_root: loading kmods from internal overlay
[ 10.608255] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.624187] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 12.785249] jffs2: notice: (516) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum
(20 unchecked, 1 orphan) and 31 of xref (1 dead, 0 orphan) found.
[ 12.817554] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.840864] block: extroot: not configured
[ 14.093476] jffs2: notice: (514) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum
(20 unchecked, 1 orphan) and 31 of xref (1 dead, 0 orphan) found.
[ 14.873502] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 14.896127] block: extroot: not configured
[ 14.905906] mount_root: switching to jffs2 overlay
[ 14.928650] overlayfs: upper fs does not support tmpfile.
[ 14.947872] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 15.175047] procd: – early –
[ 15.181004] procd: – watchdog –
[ 15.940544] procd: – watchdog –
[ 15.966893] procd: – ubus –
[ 16.310371] random: ubusd: uninitialized urandom read (4 bytes read)
[ 16.340542] random: ubusd: uninitialized urandom read (4 bytes read)
[ 16.479286] procd: – init –
[ 19.317410] kmodloader: loading kernel modules from /etc/modules.d/*
[ 19.696280] urngd: jent-rng init failed, err: 2
[ 19.973013] tun: Universal TUN/TAP device driver, 1.6
[ 20.012469] nat46: module (version 362640b41ae52b732d9e9729e61ac555492442a3) loaded.
[ 20.189122] GACT probability on
[ 20.207895] Mirror/redirect action on
[ 20.258676] u32 classifier
[ 20.264134] input device check on
[ 20.271426] Actions configured
[ 20.336632] fuse: init (API version 7.31)
[ 20.373475] usbcore: registered new interface driver cdc_acm
[ 20.384823] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 20.427400] usbcore: registered new interface driver cdc_wdm
[ 20.443793] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35
[ 20.458982] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32
[ 20.488194] usbcore: registered new interface driver ipheth
[ 20.580663] usbcore: registered new interface driver usblp
[ 20.609380] usbcore: registered new interface driver usbserial_generic
[ 20.622570] usbserial: USB Serial support registered for generic
[ 20.672426] xt_time: kernel timezone is -0000
[ 20.685196] usbcore: registered new interface driver cdc_ether
[ 20.702952] usbcore: registered new interface driver cdc_ncm
[ 20.802333] usbcore: registered new interface driver huawei_cdc_ncm
[ 20.921558] PPP generic driver version 2.4.2
[ 20.933782] NET: Registered protocol family 24
[ 20.947417] usbcore: registered new interface driver qmi_wwan
[ 20.963880] usbcore: registered new interface driver rndis_host
[ 21.004555] usbcore: registered new interface driver sierra
[ 21.015837] usbserial: USB Serial support registered for Sierra USB modem
[ 21.033862] usbcore: registered new interface driver sierra_net
[ 21.058717] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 21.074398] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
[ 21.120036] usbcore: registered new interface driver cdc_mbim
[ 21.141327] usbcore: registered new interface driver option
[ 21.152620] usbserial: USB Serial support registered for GSM modem (1-port)
[ 21.175206] usbcore: registered new interface driver qcserial
[ 21.186863] usbserial: USB Serial support registered for Qualcomm USB modem
[ 21.228892] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device “factory”
[ 21.243371] ieee80211 phy0: rt2x00_set_rt: Info – RT chipset 6352, rev 0500 detected
[ 21.258841] ieee80211 phy0: rt2x00_set_rf: Info – RF chipset 7620 detected
[ 21.272680] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’
[ 21.386827] usbcore: registered new interface driver rt2800usb
[ 21.402090] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 30.141762] random: crng init done
[ 48.186668] 8021q: adding VLAN 0 to HW filter on device eth0
[ 48.225183] br-lan: port 1(eth0.1) entered blocking state
[ 48.236039] br-lan: port 1(eth0.1) entered disabled state
[ 48.247252] device eth0.1 entered promiscuous mode
[ 48.256856] device eth0 entered promiscuous mode
[ 48.353401] br-lan: port 1(eth0.1) entered blocking state
[ 48.364236] br-lan: port 1(eth0.1) entered forwarding state
[ 49.190195] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 57.532167] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration start
[ 57.548838] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration end
[ 61.671482] ieee80211 phy0: rt2800_loft_iq_calibration: Info – LOFT Calibration Done!
[ 61.691082] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[ 61.719002] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 0, (gain= f, phase= 0)
[ 61.738120] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[ 61.766031] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 1, (gain= f, phase=3e)
[ 61.784268] ieee80211 phy0: rt2800_loft_iq_calibration: Info – TX IQ Calibration Done!
[ 61.813570] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=-3, Ph_rx=0
[ 61.838934] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=1, Ph_rx=-2
[ 61.922090] br-lan: port 2(wlan0) entered blocking state
[ 61.932763] br-lan: port 2(wlan0) entered disabled state
[ 61.943807] device wlan0 entered promiscuous mode
[ 64.198895] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 64.211865] br-lan: port 2(wlan0) entered blocking state
[ 64.222506] br-lan: port 2(wlan0) entered forwarding state
[ 82.031153] device wlan0 left promiscuous mode
[ 82.040248] br-lan: port 2(wlan0) entered disabled state
[ 83.282597] br-lan: port 1(eth0.1) entered disabled state
[ 83.450420] device eth0.1 left promiscuous mode
[ 83.459757] br-lan: port 1(eth0.1) entered disabled state
[ 85.031067] device eth0 left promiscuous mode
[ 92.926848] 8021q: adding VLAN 0 to HW filter on device eth0
[ 92.965690] br-lan: port 1(eth0.1) entered blocking state
[ 92.976520] br-lan: port 1(eth0.1) entered disabled state
[ 92.987724] device eth0.1 entered promiscuous mode
[ 92.997329] device eth0 entered promiscuous mode
[ 93.085485] br-lan: port 1(eth0.1) entered blocking state
[ 93.096280] br-lan: port 1(eth0.1) entered forwarding state
[ 93.943207] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 97.530167] ksmbd: kill command received
[ 99.207787] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration start
[ 99.224461] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info – RF Tx self calibration end
[ 104.099802] ksmbd: kill command received
[ 104.473166] ieee80211 phy0: rt2800_loft_iq_calibration: Info – LOFT Calibration Done!
[ 104.492763] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[ 104.520684] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 0, (gain= 1, phase= 1)
[ 104.539802] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Start!
[ 104.567729] ieee80211 phy0: rt2800_iq_search: Info – IQCalibration Done! CH = 1, (gain= 3, phase=3e)
[ 104.585966] ieee80211 phy0: rt2800_loft_iq_calibration: Info – TX IQ Calibration Done!
[ 104.615359] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=-4, Ph_rx=0
[ 104.643159] ieee80211 phy0: rt2800_rxiq_calibration: Info – RXIQ G_imb=0, Ph_rx=3
[ 104.756494] br-lan: port 2(wlan0) entered blocking state
[ 104.767170] br-lan: port 2(wlan0) entered disabled state
[ 104.778293] device wlan0 entered promiscuous mode
[ 106.862360] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 106.875319] br-lan: port 2(wlan0) entered blocking state
[ 106.885954] br-lan: port 2(wlan0) entered forwarding state
Just another Vivaldi.net Userblogs Sites site
